1. Both the semi-automatic and manual presses must be equipped with a two-hand brake switch. It is strictly prohibited to press the pedal or one-hand start switch.

2. After the high-flush adjustment, after the normal stamping, close the soundproof box (except for the product 8065 side inspection packaging).

3. During continuous stamping, employees cannot take the product by hand within 1M of the press.

4. When the technician adjusts the machine, only one person can debug, and no two people should debug.

5. The technician adjusts the feeding of the machine, which can only be outside the machine, and the distance is not less than 1M.

6. Always tighten the screws when the mold is placed. Check the screws for 4 hours to stop the screws.

7. When the mold has problems in the production process, it is not necessary to unload the mold. When repairing directly on the machine tool, the power of the injection molding machine must be turned off and the maintenance label must be hung on the power supply box to implement the mold repair.

8. All tools will be returned to the toolbox after they are used up, and they should not be placed on the machine to prevent the tool from slipping and hurting people.

9. When the machine is not in production, cut off the power supply in time.

10. When using short workpieces, use special tools and do not feed or take them by hand.

11. The producer should stand properly, keep the hand and head at a certain distance from the punching machine, and always pay attention to the punching action. It is strictly forbidden to chat with others.

12. It is strictly forbidden for the operator and the molder to reach into the mold during production.

13. When installing the suction fan, the operator must not put the hand on the motor to clean the waste.

14. It is strictly forbidden to wear slippers when going to work, so as to avoid the molds and iron blocks in the workshop. The squad leader, fitter, and mold repairer must wear protective shoes when they go to work;

15. Male workers are strictly forbidden to keep long hair, and female workers must make long hairs to prevent them from getting caught in the flywheel.

16. Other oils such as white oil, alcohol, detergent, etc. should pay attention to fire prevention.

17. Gloves should be worn when packing materials, scraps and molds to avoid scratching your hands.

18. When oil is available, it must be cleaned up in time to avoid slipping.

19. Do not wear gloves when drilling and milling machines; use a mask and eye shield when using the grinder to protect yourself.

20. Pay attention to dragging the mold to prevent it from falling on the floor (to lower the flatbed to the lowest mold).

21. It is strictly forbidden for non-electrician personnel to pick up and repair the machine.

22. It is strictly forbidden to blow the air gun at the person and it is easy to hurt the eyes.

23. The operator is required to wear earplugs.

24. When the machine is abnormal, turn off the power and then find the technician on duty in time. You can't handle it without authorization.

25. When a new employee goes to work on the first day, the team leader must explain the safety practices to him. He will study the safety procedures once a day for the first week.

26. When adjusting the machine, be sure to adjust the machine to single action. It is strictly forbidden to play the discharge belt.

27. Do not store any flammable or explosive materials under the electric gate.

28. It is strictly forbidden for the operator to chase and chase in the workshop to avoid falling, knocking down the product or hurting himself.

29. Check the equipment according to the inspection contents on the equipment check card, paying special attention to the normal operation of the punching guide and brake device, and the single punch and continuous punch functions are clear.

30. When installing the mold on the small punch (10T), first loosen the locking device of the guide rail, install the upper and lower molds, and then adjust the travel of the guide rail until the requirements are met and the fastening device is locked. After hitting the single stroke, after locking the upper mold, the lower mold is locked after the oil pressure is clamped, and another inspection is performed before production. ·

31. When discharging materials or manually feeding the blanks, special tools (pliers, hooks) must be used. It is strictly forbidden to send and take the blanks by hand. A single switch must hurt the hand and a double switch. The machine should not leak oil, otherwise it will fall. Do not expose the power supply, it is dangerous.

32. Wear gloves when punching iron pieces, concentrate your mind, or hurt your hand.

33. In the work, first check whether the equipment is running abnormally, such as single, continuous, unsatisfactory operation or electrical failure, and immediately stop the machine and find the technician on duty.

34. It is strictly forbidden to use the foot switch on the press, and all the original equipment of the machine is removed.

35. When cleaning and inspecting the equipment, the power must be turned off and operated.

36. Cut off the power supply, clean and scrub the work surface, remove the mold and store it in the warehouse, and check the lubrication system oil every week.